Q: What is the material used in HERCULINER?
A: HERCULINER is a mixture of polyurethane coating with rubber
    granules to provide a tough, textured finish.

back to top

Q: How can it be applied?
A: HERCULINER can be applied with a brush/roller or with a spray
    compressor. (Brush and two (2) rollers are included with each
    kit.) It must be applied in a well ventilated area.

back to top

Q: What colors are available?
A: Black, Gray Red & White.

back to top

Q: Where can I buy it?
A: Click on "stores near you" or go to www.247autoparts.com to get a kit of your own.
 

back to top
 

Q: How much is the cost and in what size containers will it
     be available?
A: Suggested retail on the black kit is $99.99, which includes
    one (1) gallon. Additional black quarts are available for $29.99.
    Red, gray & white kits are available for $139.99. Red, gray and
    white quarts are available for $39.99.

back to top

Q: What surfaces will it bond to?
A: HERCULINER will bond to most clean/dry surfaces, including
    painted or primed steel. Prepping the surface is critical for
    best results; instructions are included with the kit, or you
    can just click on "Instructions" icon on this or any other page
    of the HERCULINER site.


 

back to top

Q: What is the shelf life of HERCULINER?
A: If unopened, HERCULINER can be stored for several years. 
 

back to top

Q: How tough is HERCULINER?
A: HERCULINER won’t chip, flake or peel and is resistant to
    damage from gasoline and most chemicals & solvents. It
    can withstand years of heavy duty use.

 

back to top

Q: How can I remove HERCULINER once it's applied?
A: You can use Xylene while product is still wet, but if it dries,
    it's permanent.
 

back to top

 

Q: What happens if I get  HERCULINER on my hands?
A: Clean off immediately with Xylene, then wash hands with
    soap and water.

 

back to top

Q: How long does it take HERCULINER to dry?
A: You should allow HERCULINER to dry about 9-12 hours before
    any light use and allow 24 hours for a complete cure. Curing
    begins when HERCULINER is exposed to atmospheric moisture.
    Therefore, with higher humidity, curing time is shorter.
 

back to top

Q: How thick should it be applied?
A: First coat forms a good base. After 1 hour to 1 ½ hours to
    dry; then apply a second coat that will cover any open pores.
    One (1) gallon covers 6’ beds with 2 coats; an extra quart is
    needed for 8’ beds.

 

back to top

Q: Can you repair a section that has been damaged?
A: Yes, HERCULINER adheres to itself, while other coatings do
    not and would have to be removed for gouging repair.
 

back to top


 

Q: Is HERCULINER flammable?
A: Yes, but after drying, it is no longer flammable.


 

back to top

Q: Can I apply HERCULINER in the winter?
A: Yes, HERCULINER can be applied between 32° F and 95° F.
    However, the colder the temperature and the lower the
    humidity, the longer the curing process will take. Additionally,
    it MUST BE APPLIED IN A WELL VENTILATED AREA.
 

back to top


 

Q: What is the difference between our coating formula
     versus the other spray-on coatings out there?
A: HERCULINER has a proprietary polyurethane and rubber formula.
    HERCULINER is the only do-it-yourself bedliner with a tough,
    thick, skid-resistant finish that won’t chip, flake or peel.


 

back to top

Q: What is included in a kit?
A: 1 gallon of protective coating
    2 rollers for easy application
    1 abrasive pad for scuffing/prepping bed
    1 roller handle
    1 gallon can opener
    1 - 2" brush for tight spots/corners
    Plus: Bed liner application instructions in English, French, and
    Spanish AND application instructions for other uses (also in
    English, French, and Spanish).
 

back to top


 

Q: What is not included in a kit that will be needed to do the
     job right?
A: One Quart of Xylene, Acetone or MEK (solution to prep the
    surface of the bed before coating)
    Rubber gloves
    Stir stick (We recommend a drill with a paint mixing attachment.)
    Paint tray and some rags
    Tape for masking off areas


 

back to top

Q: What kind of warranty does HERCULINER have?
A: We warranty the product against faulty manufacture and
    defective materials. We cannot accept liability for application
    or use of this product (too many variables, proper
    prepping/cleaning of surface, application methods, etc.).
 

back to top
 

Q: What is the average cost for a dealer installed spray-on
     bed liner?
A: There are a number of different products and dealers offering
    bed liner spray-on services. Finished product mil thickness, skid
    resistant properties, and costs vary by location from $300.00
    to over $500.00.
 

back to top
 

Q: Can I use HERCULINER Coating for other uses?
A: Yes, the HERCULINER Coating can be used on an array of
    surfaces from concrete to plastic as well as an undercoating
    to ramp coatings, etc. Just go to the Other Uses page and 
    see what other surfaces you can apply it to.

 

back to top

 

Visit our Store Locator or Buy Now at www.247autoparts.com!